Exactly How To Install A Tub (For Beginners).
Exactly How To Install A Tub (For Beginners).
Blog Article
What are your opinions regarding Tools You Need to Install a New Bathtub ?
Mounting a bath tub isn't exactly rocket science, however it does need strong plumbing, woodworking, and sometimes, tiling skills. Replacing an old tub with a new one is likewise a reasonably hard task. If the old bathtub is conveniently accessible, the project can move rapidly; if you need to open up a wall surface to eliminate the old bathtub and also place the brand-new tub, the job is a lot harder. In either situation, the job is within a house handyman's abilities, although you will need a helper to vacate the old bathtub and also embeded in the brand-new one. Ensure you have qualified yourself for the work as well as are comfortable attempting it. Rather than working with a specialist to take over a halfway-completed project, it is better to think about employing one before you start. Possibilities are you may require a specialist plumber to make tube links.
This short article will certainly aid you mount a brand-new bath tub in your bathroom if you have already bought a brand-new bathtub and also do not require to alter the setup of your previous water system pipelines.
Your devices as well as product list ought to comprise the following:
Removing Old Taps
If you require to change old faucets with brand-new ones as a part of your setup, then the first thing you should do is separate the water. After doing so, activate the taps to drain any water continuing to be in the system. The process of eliminating the existing taps can be quite troublesome due to the restricted access that is usually the instance.
Make use of a basin wrench (crowsfoot spanner) or a tap tool to reverse the nut that links the supply pipes to the taps. Have a towel all set for the remaining water that will originate from the pipes. Once the supply pipelines have actually been eliminated, use the very same device to loosen the nut that holds the faucets onto the bath/basin. You will certainly need to quit the solitary taps from transforming during this process. As soon as the taps have been eliminated, the holes in the bath/basin will need to be cleaned up of any old securing compound.
Before going on to fit the new taps, contrast the pipe links on the old taps to the new faucets. If the old taps are longer than the brand-new taps, after that a shank adapter is needed for the new faucets to fit.
Fitting New Touches
If the tails of the brand-new taps are plastic, after that you will require a plastic connector to stop damages to the thread. One end of the port fits on the plastic tail of the tap and also the other end gives a connection to the existent supply pipelines.
If you need to fit a monobloc, after that you will need reducing couplers, which links the 10mm pipe of the monobloc to the common 15mm supply pipe.
Next off, position the faucet in the mounting opening in the bath/basin guaranteeing that the washing machines are in area between the faucet and the sink. Protect the faucet in position with the producer given backnut. When the faucet is securely in position, the supply pipes can be linked to the tails of the taps. The taps can either be attached by using corrugated copper piping or with typical faucet connectors. The previous kind ought to be attached to the tap ends initially, tightening up only by hand. The supply pipelines can later on be linked to the various other end. Tighten both ends with a spanner after both ends have been attached.
Mounting the Bathtub
Utilizing the two wood boards under its feet, position the bathtub in the needed setting. The wood boards are helpful in evenly spreading the weight of the tub over the location of the boards as opposed to concentrating all the weight onto 4 tiny points.
The following objective is to ensure that the tub is leveled all round. This can be attained by examining the spirit level as well as readjusting the feet on the bath tub until the spirit level checks out level.
To set up faucets, fit all-time low of the outermost flexible tap connector to the suitable supply pipe by making a compression join; then do the exact same for the other tap.
Turn on the supply of water and check all joints and new pipework for leakages and tighten them if needed. Load the bath tub as well as additionally check the overflow outlet and the typical electrical outlet for leakages.
Ultimately, deal with the bathroom paneling as described in the manufacturer's instruction manual. Tiling and sealing around the bathtub ought to wait up until the tub has been utilized a minimum of once as this will certainly resolve it right into its last placement.
Preparing for the Installation
Firstly, the supporting frame provided with the bathroom must be fitted (if required) according to the manufacturer's instructions. Next, fit the taps or mixer to the bathtub. When suitable the faucet block, it is important to see to it that if the faucet features a plastic washing machine, it is fitted in between the bath and the taps. On a plastic bath, it is also sensible to fit a sustaining plate under the faucets device to avoid stress on the tub.
Fit the flexible tap connectors to the bottom of both faucets utilizing 2 nuts as well as olives (in some cases supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the outlet through the hole in the bathroom. Utilize the nut supplied by the producer to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the adaptable overflow pipeline to the overflow electrical outlet. After that, screw the pipeline to the overflow face which need to be fitted inside the bath. Make sure you make use of every one of the supplied washers.
Attach the catch to the bottom of the waste outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Connect the bottom of the overflow tube in a comparable manner.The bath should currently prepare to be fitted in its last setting.
Tiling Around the Bathtub
In the location where the bath meets the floor tile, it is required to secure the accompanies a silicone rubber caulking. This is essential as the fitting can relocate enough to fracture a stiff seal, causing the water to pass through the wall in between the bath and also the tiling, causing problems with wetness as well as possible leakages to the ceiling below.
You can pick from a range of coloured sealers to blend in your components as well as fittings. They are offered in tubes and cartridges, as well as are capable of securing gaps approximately a width of 3mm (1/8 inch). If you have a bigger void to fill up, you can load it with twists of drenched newspaper or soft rope. Bear in mind to always load the bathtub with water prior to sealing, to enable the movement experienced when the bathtub is in use. The sealer can break rather early if you do not think about this movement prior to securing.
Additionally, ceramic coving or quadrant floor tiles can be used to border the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as reduce to size, are likewise conveniently available on the marketplace. It is advisable to fit the ceramic tiles making use of water-resistant or water resistant glue as well as cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I came across that blog posting on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround when doing a search on the web. Sharing is nice. You won't know, you may very well be doing someone a favor. We value reading our article about Installing A Bathtub.
Source Report this page